论文/Improved understanding of physics processes in pedestal structure, leading to improved predictive capability for ITER提交纠错

Improved understanding of physics processes in pedestal structure, leading to improved predictive capability for ITER

文献资料

作者:
  • R.J. Groebner
  • C.S. Chang
  • J.W. Hughes
  • R. Maingi
  • P.B. Snyder
  • X.Q. Xu
  • J.A. Boedo
  • D.P. Boyle
  • J.D. Callen
  • J.M. Canik
  • I. Cziegler
  • E.M. Davis
  • A. Diallo
  • P.H. Diamond
  • J.D. Elder
  • D.P. Eldon
  • D.R. Ernst
  • D.P. Fulton
  • M. Landreman
  • A.W. Leonard
  • J.D. Lore
  • T.H. Osborne
  • A.Y. Pankin
  • S.E. Parker
  • T.L. Rhodes
  • S.P. Smith
  • A.C. Sontag
  • W.M. Stacey
  • J. Walk
  • W. Wan
  • E.H.-J. Wang
  • J.G. Watkins
  • A.E. White
  • D.G. Whyte
  • Z. Yan
  • E.A. Belli
  • B.D. Bray
  • J. Candy
  • R.M. Churchill
  • T.M. Deterly
  • E.J. Doyle
  • M.E. Fenstermacher
  • N.M. Ferraro
  • A.E. Hubbard
  • I. Joseph
  • J.E. Kinsey
  • B. LaBombard
  • C.J. Lasnier
  • Z. Lin
  • B.L. Lipschultz
  • C. Liu
  • Y. Ma
  • G.R. McKee
  • D.M. Ponce
  • J.C. Rost
  • L. Schmitz
  • G.M. Staebler
  • L.E. Sugiyama
  • J.L. Terry
  • M.V. Umansky
  • R.E. Waltz
  • S.M. Wolfe
  • L. Zeng
  • S.J. Zweben
署名说明:
暂无资料
期刊/出版物:
DOI:
10.1088/0029-5515/53/9/093024
语言:
英语
文献类型:
journal-article
作者署名机构:
对应版本
关联作者稿
署名机构
  • id
    1
    名称
    General Atomics
  • id
    2
    名称
    Princeton Plasma Physics Laboratory
  • id
    3
    名称
    Massachusetts Institute of Technology
  • id
    4
    名称
    Lawrence Livermore National Laboratory
  • id
    5
    名称
    University of California San Diego
  • id
    6
    名称
    University of Wisconsin-Madison
  • id
    7
    名称
    Oak Ridge National Laboratory
  • id
    8
    名称
    University of Toronto Institute for Aerospace Studies
  • id
    9
    名称
    University of California Irvine
  • id
    10
    名称
    Tech-X
  • id
    11
    名称
    University of Colorado at Boulder
  • id
    12
    名称
    University of California Los Angeles
  • id
    13
    名称
    Georgia Institute of Technology
  • id
    14
    名称
    Sandia National Laboratory
authors
  • 名称
    R.J. Groebner
    affiliation_ids
    • 1
  • 名称
    C.S. Chang
    affiliation_ids
    • 2
  • 名称
    J.W. Hughes
    affiliation_ids
    • 3
  • 名称
    R. Maingi
    affiliation_ids
    • 2
  • 名称
    P.B. Snyder
    affiliation_ids
    • 1
  • 名称
    X.Q. Xu
    affiliation_ids
    • 4
  • 名称
    J.A. Boedo
    affiliation_ids
    • 5
  • 名称
    D.P. Boyle
    affiliation_ids
    • 2
  • 名称
    J.D. Callen
    affiliation_ids
    • 6
  • 名称
    J.M. Canik
    affiliation_ids
    • 7
  • 名称
    I. Cziegler
    affiliation_ids
    • 5
  • 名称
    E.M. Davis
    affiliation_ids
    • 3
  • 名称
    A. Diallo
    affiliation_ids
    • 2
  • 名称
    P.H. Diamond
    affiliation_ids
    • 5
  • 名称
    J.D. Elder
    affiliation_ids
    • 8
  • 名称
    D.P. Eldon
    affiliation_ids
    • 5
  • 名称
    D.R. Ernst
    affiliation_ids
    • 3
  • 名称
    D.P. Fulton
    affiliation_ids
    • 9
  • 名称
    M. Landreman
    affiliation_ids
    • 3
  • 名称
    A.W. Leonard
    affiliation_ids
    • 1
  • 名称
    J.D. Lore
    affiliation_ids
    • 7
  • 名称
    T.H. Osborne
    affiliation_ids
    • 1
  • 名称
    A.Y. Pankin
    affiliation_ids
    • 10
  • 名称
    S.E. Parker
    affiliation_ids
    • 11
  • 名称
    T.L. Rhodes
    affiliation_ids
    • 12
  • 名称
    S.P. Smith
    affiliation_ids
    • 1
  • 名称
    A.C. Sontag
    affiliation_ids
    • 7
  • 名称
    W.M. Stacey
    affiliation_ids
    • 13
  • 名称
    J. Walk
    affiliation_ids
    • 3
  • 名称
    W. Wan
    affiliation_ids
    • 11
  • 名称
    E.H.-J. Wang
    affiliation_ids
    • 4
  • 名称
    J.G. Watkins
    affiliation_ids
    • 14
  • 名称
    A.E. White
    affiliation_ids
    • 3
  • 名称
    D.G. Whyte
    affiliation_ids
    • 3
  • 名称
    Z. Yan
    affiliation_ids
    • 6
  • 名称
    E.A. Belli
    affiliation_ids
    • 1
  • 名称
    B.D. Bray
    affiliation_ids
    • 1
  • 名称
    J. Candy
    affiliation_ids
    • 1
  • 名称
    R.M. Churchill
    affiliation_ids
    • 3
  • 名称
    T.M. Deterly
    affiliation_ids
    • 1
  • 名称
    E.J. Doyle
    affiliation_ids
    • 12
  • 名称
    M.E. Fenstermacher
    affiliation_ids
    • 4
  • 名称
    N.M. Ferraro
    affiliation_ids
    • 1
  • 名称
    A.E. Hubbard
    affiliation_ids
    • 3
  • 名称
    I. Joseph
    affiliation_ids
    • 4
  • 名称
    J.E. Kinsey
    affiliation_ids
    • 1
  • 名称
    B. LaBombard
    affiliation_ids
    • 3
  • 名称
    C.J. Lasnier
    affiliation_ids
    • 4
  • 名称
    Z. Lin
    affiliation_ids
    • 9
  • 名称
    B.L. Lipschultz
    affiliation_ids
    • 3
  • 名称
    C. Liu
    affiliation_ids
    • 1
  • 名称
    Y. Ma
    affiliation_ids
    • 3
  • 名称
    G.R. McKee
    affiliation_ids
    • 6
  • 名称
    D.M. Ponce
    affiliation_ids
    • 1
  • 名称
    J.C. Rost
    affiliation_ids
    • 3
  • 名称
    L. Schmitz
    affiliation_ids
    • 12
  • 名称
    G.M. Staebler
    affiliation_ids
    • 1
  • 名称
    L.E. Sugiyama
    affiliation_ids
    • 3
  • 名称
    J.L. Terry
    affiliation_ids
    • 3
  • 名称
    M.V. Umansky
    affiliation_ids
    • 4
  • 名称
    R.E. Waltz
    affiliation_ids
    • 1
  • 名称
    S.M. Wolfe
    affiliation_ids
    • 3
  • 名称
    L. Zeng
    affiliation_ids
    • 12
  • 名称
    S.J. Zweben
    affiliation_ids
    • 2
通讯作者:
  • 名称
    R.J. Groebner
    affiliation
    General Atomics
    email
    groebner@fusion.gat.com
    对应版本
    关联作者稿
    designation
    e-mail contact of main author
发表日期:
online
2013-08-21
print
2013-09-01
卷号:
53
期号:
9
页码或文章编号:
article_number
093024
local_manuscript_pdf_pages
69
说明
69为关联作者稿PDF物理页数,含库封面、正文和独立图页;不是期刊页码。
arXiv 标识:
暂无资料

研究内容与方法

关键词:
classification_system
PACS
codes
  • 52.55.Fa
  • 52.25.Fi
  • 52.35.Py
  • 52.35.Ra
  • 52.70.Kz
说明
原稿列PACS分类号,未列独立文字关键词。
研究领域:
  • 磁约束聚变
  • 托卡马克H模台基物理
  • 等离子体稳定性与输运
研究问题:
哪些物理过程控制H模台基的压力高度、宽度以及密度和温度剖面?跨C-Mod、DIII-D和NSTX的实验与理论模型能否建立可外推至ITER的台基预测能力?
实验装置:
使用软件:
使用数据:
  • 名称
    C-Mod、DIII-D、NSTX台基实验数据
    relationship
    研究使用
    说明
    高分辨Thomson散射的电子温度和密度剖面;可得时使用电荷交换复合光谱的离子温度及低Z杂质密度;用于共同流程和稳定性分析。
  • 名称
    DIII-D discharge 131997
    relationship
    研究使用
    说明
    GYRO、GEM、HD7台基微不稳定性比较输入,见图15。

出版与资源

收稿日期:
暂无资料
接收日期:
暂无资料
出版机构:
IOP Publishing
获取方式:
status
机构库有公开全文记录
对应版本
eScholarship作者稿
publisher_status_as_indexed
OpenAlex既有快照标为bronze
access_check
2026-11-06:机构库网页403,出版商页面404,当前在线可下载性未确认;本地关联PDF可读。
使用许可:
repository_manuscript
license
CC BY-NC-ND 4.0
publisher_version
说明
Crossref列版权政策链接;未据此认定正式出版版使用同一CC许可。
出版页面:
https://iopscience.iop.org/article/10.1088/0029-5515/53/9/093024
配套代码:
暂无资料
配套数据:
暂无资料
补充材料:
暂无资料
资助信息:
funders
  • 名称
    US Department of Energy
    grant_numbers
    • DE-FC02-04ER54698
    • DE-FG02-95ER54309
    • DE-FG02-00ER54538
    • DE-AC52-07NA27344
    • DE-FC02-93ER54186
    • DE-AC05-00OR22725
    • DE-AC02-09CH11466
    • DE-AC04-94AL85000
    • DE-FG03-94ER54271
    • DE-FG02-08ER54984
    • DE-FG02-07ER54917
    • DE-FC02-05ER54816
    • DE-FG02-89ER53296
    • DE-FG02-08ER54999
    scope
    部分支持本工作
  • 名称
    Natural Sciences and Engineering Research Council of Canada
    scope
    University of Toronto开展的工作
更正与撤稿信息:
暂无资料

关联研究与影响

相关论文:
  • DOI
    10.1088/0029-5515/47/6/S02
    relationship
    本文引用
    reference_number_in_published_record
    1
    说明
    ITER物理基础与芯部约束背景
  • DOI
    10.1063/1.3122146
    relationship
    本文引用
    reference_number_in_published_record
    3
    说明
    EPED模型基础
  • DOI
    10.1063/1.873240
    relationship
    本文引用
    reference_number_in_published_record
    12
    说明
    Sauter自举电流模型
  • DOI
    10.1088/0741-3335/50/9/095010
    relationship
    本文引用
    reference_number_in_published_record
    18
    说明
    NEO动理学计算
  • DOI
    10.1088/0741-3335/54/11/115006
    relationship
    本文引用
    reference_number_in_published_record
    19
    说明
    全局漂移动理学模型
  • DOI
    10.1088/0029-5515/51/10/103016
    relationship
    本文引用
    reference_number_in_published_record
    42
    说明
    台基高度与宽度预测
相关著作:
暂无资料
历史引用资料(口径待核):
count
65
source
Crossref
metric
is-referenced-by-count
获取日期
2026-11-06
record_indexed_at
2026-09-20T07:09:05Z
引用统计来源:
provider
Crossref
metric
is-referenced-by-count
引用统计日期:
获取日期
2026-11-06
record_indexed_at
2026-09-20T07:09:05Z
说明
访问日期不等同索引更新日期。

基本资料

审稿意见:
暂无资料
外部用户评论:
暂无资料
论文版本:
译文:
  • 语言
    zh-CN
    对应版本
    关联机构库作者稿
    source_section
    Abstract,作者稿第2页
    method
    本次AI翻译,非作者或出版商授权译文
    原文
    实验、理论与建模的联合研究提高了对ITER台基高度预测的信心。本工作属于美国能源部2011财年联合研究目标,旨在识别控制H模台基结构的物理过程。研究包括C-Mod、DIII-D和NSTX上的实验,以及利用基于理论的建模程序解释实验数据。结果增强了对剥离—气球模稳定性、自举电流、台基宽度和高度标度模型预测能力的信心,同时指出了仍需进一步研究的方面。台基压力高度模型在现有装置跨越20倍的压力范围内作出了良好预测,为预测ITER的最大台基压力高度提供了坚实基础;ITER预测需在现有数据集之外再外推约3倍。研究还检验了可能影响台基电子密度和电子温度剖面的新经典输运、古典型输运(paleoclassical transport)、电子温度梯度湍流和中性粒子补给等过程。这些过程都可能重要,其重要程度取决于等离子体运行状态。多个电磁回旋动理学程序的研究表明,台基内及台基顶部的梯度可以驱动多种不稳定性。

程序计算

库内被引次数:
首批录入完成后计算
是否库内高被引:
尚未计算
质量分数:
暂无资料
完备性评分:
暂无资料
可信度评分:
暂无资料
聚变相关度评分:
暂无资料

原文摘要

Joint experiment/theory/modelling research has led to increased confidence in predictions of the pedestal height in ITER. This work was performed as part of a US Department of Energy Joint Research Target in FY11 to identify physics processes that control the H-mode pedestal structure. The study included experiments on C-Mod, DIII-D and NSTX as well as interpretation of experimental data with theory-based modelling codes. This work provides increased confidence in the ability of models for peeling–ballooning stability, bootstrap current, pedestal width and pedestal height scaling to make correct predictions, with some areas needing further work also being identified. A model for pedestal pressure height has made good predictions in existing machines for a range in pressure of a factor of 20. This provides a solid basis for predicting the maximum pedestal pressure height in ITER, which is found to be an extrapolation of a factor of 3 beyond the existing data set. Models were studied for a number of processes that are proposed to play a role in the pedestal n e and T e profiles. These processes include neoclassical transport, paleoclassical transport, electron temperature gradient turbulence and neutral fuelling. All of these processes may be important, with the importance being dependent on the plasma regime. Studies with several electromagnetic gyrokinetic codes show that the gradients in and on top of the pedestal can drive a number of instabilities.

原始程序说明(PROGRAM SUMMARY)

暂无资料

研究背景

对应版本
关联作者稿
原文
H模台基既直接贡献约束,也为芯部输运提供边界条件,较高台基压力通常有利于芯部压力和聚变性能。ITER及未来装置的台基优化还必须同时满足小或无ELM、杂质屏蔽及气体/弹丸补给等要求,因此需要可预测的台基模型。

研究目标

对应版本
关联作者稿
原文
通过美国能源部FY2011台基物理联合研究目标,协调C-Mod、DIII-D和NSTX实验、理论和建模,识别控制台基结构的共性物理;检验压力高度和宽度的稳定性约束,并评估控制独立密度、温度剖面的输运与补给过程,以提高ITER预测和优化能力。

方法与实验设计

依据关联作者稿整理:协调C-Mod、DIII-D及NSTX实验并采用共同分析流程。用高分辨Thomson散射测量电子温度与密度,在可得条件下用电荷交换复合光谱测量离子温度和低Z杂质密度;用Python工具拟合台基剖面,EFIT构造受实测压力与Sauter自举电流约束的动理学平衡,通过扰动压力和电流扫描稳定性空间,并用ELITE分析剥离—气球模阈值。以EPED组合全局剥离—气球模和局域动理学气球模约束,比较台基高度、宽度及ITER外推。用XGC0、NEO、GPDKC检验自举电流及输运;对GEM、GYRO、HD7进行电磁回旋动理学基准比较,检验几何模型差异;另用GS2、BOUT++及OEDGE分别研究微不稳定性、EDA台基波动和中性粒子电离源。

主要结果

依据关联作者稿整理:剥离—气球模稳定性边界与三装置观测总体相容。EPED在C-Mod和DIII-D上预测Type-I ELM发生前台基高度与宽度的精度约为20%;已有压力验证范围约跨20倍,ITER台基压力预测需进一步外推约3倍。对ITER基线情景,假定台基电子密度约7×10^19 m^-3,模型给出台基β_N约0.6、归一化极向磁通宽度约0.04(约4.4 cm)及台基离子温度约4.5 keV;是否达到Q=10仍依赖芯部输运模型。这些是预测而非ITER实测。新动理学自举电流模型在低碰撞率下与Sauter结果总体一致,高碰撞率下可显著不同。新经典输运、中性粒子补给、paleoclassical输运及ETG湍流均可能影响密度和温度结构;部分条件需要额外反常输运。

讨论与科学意义

对应版本
关联作者稿
原文
压力剖面与边缘电流(含显著自举电流)共同决定全局剥离—气球模和局域KBM约束,是压力台基预测的主要依据。但压力高度预测成功不等于各密度、温度剖面机制已被唯一确定。波动观测虽具KBM特征,尚未完成唯一识别;微不稳定性模拟对磁几何敏感,跨装置结果复杂。粒子输运、内向箍缩和中性粒子补给都可能影响密度结构,其权重取决于运行状态,需在综合模型中自洽处理。

局限与后续方向

依据关联作者稿整理:EPED主要预测Type-I ELM前的台基极限,对无ELM或Type-III ELM等其他状态可能需要额外物理;NSTX低纵横比台基宽度尚未得到充分定量描述。高碰撞率自举电流模型间存在差异,需要边缘电流密度测量验证。KBM是否实际限制台基仍需实验与模拟进一步辨认;某些全局计算需人为展平q剖面才出现相关模态。ETG引起的输运量及台基内向粒子箍缩尚无直接清晰测量。回旋动理学计算受几何表示和强梯度下近似有效性限制。下一步需要建立密度和/或温度剖面的预测能力,将多种输运、稳定性及补给过程自洽耦合,扩展ITER与未来装置的优化能力。

数据、代码与可复现性

对应版本
关联作者稿
available_information
  • 第2.1.2节描述跨装置共同测量、拟合和EFIT/ELITE分析流程
  • 图注给出部分DIII-D放电号、测量时刻及建模条件
  • 第3.3.1节描述GEM、GYRO、HD7同几何基准比较
limitations
  • 本文未给出可核实的配套代码仓库或软件提交版本
  • 未找到与本论文明确绑定的可下载输入/输出数据包
  • 部分分析细节转引其他论文,需要获取这些文献及原始装置数据
assessment
方法与部分工况可追溯;当前资料不足以独立完整重跑全部计算。

内容概述

站内整理(依据关联机构库作者稿第1–4节):本研究整合C-Mod、DIII-D与NSTX实验及理论建模,检验H模台基压力、宽度和密度/温度结构的控制机制。剥离—气球模与动理学气球模约束为EPED预测提供支持,在C-Mod和DIII-D的Type-I ELM条件下,高度与宽度预测精度约20%,并支持向ITER外推。独立密度、温度剖面的输运和补给机制仍未完全确定,需要更多诊断验证和自洽综合建模。

原文结论

4. Summary and discuss ion Joint experiment/theory/modeling research has led to improved understanding of the limits to the H - mode pedestal pressure profile, increased confidence in predictions of the pedestal height in ITER and new tests of models for pedestal temperature and d ensity profiles. This work was performed as part of a US DOE Joint Research Target in fiscal year 2011 and included experimental research from C - Mod, DIII - D and NSTX as well as interpretation of experimental data with several theory - based modeling codes. T he goal of the research was to identify important physics processes that control pedestal structure and work towards improved predictive capability. Two significant results of this work are that theoretical constraints on the pedestal pressure profile are consistent with a wide range of observations in these three machines and these constraints provide a good basis for understanding and predicting the pressure profile. The interplay between the total pressure profile and the edge current density profile, wi th a large contribution from the bootstrap current, provides the dominant physics for these constraints. One constraint is set by ideal finite - € n peeling - ballooning modes, which are non - local modes, predicted to be the MHD modes that t rigger Type - I ELMs. Significant work was performed to extend models for these modes to the high - field C - Mod device and the low aspect ratio NSTX 33 device. In all three machines, within error bars, the operating space is never observed to extend past the inst ability boundaries predicted for these modes. The second constraint is that kinetic ballooning modes provide a limit to the local pedestal pressure gradient. These modes are smaller scale and less virulent than peeling - ballooning modes. However, these mod es are predicted to turn on robustly when a critical pressure gradient is reached and to limit the gradient to near the critical value. Kinetic ballooning physics has provided a successful quantitative description of the pedestal width scaling in C - Mod and DIII - D. The model qualitatively captures the experimental trend that widths are higher in the low aspect ratio NSTX device than in the conventional aspect ratio machines. These two constraints on the pedestal pressure profile have been combined into one model (EPED) which predicts pedestal width and height at the onset of a Type I ELM. The model makes good predictions of the pedestal pressure widths and heights observed in C - Mod and DIII - D over a wide range of conditions. The C - Mod data have increased the highest pressure at which the model has been tested by a factor of two. A new DIII - D data set has provided improved tests of the model at large widths. These predictions are accurate to about 20% and provide a sound basis for predicting the pedestal heigh t in ITER, which is predicted to have a pressure that is an extrapolation of a factor of 3 from the existing data set. An important input to peeling - ballooning models and kinetic ballooning models is the current density profile, which is typically obtained from calculations using neoclassical bootstrap current models such as the Sauter model. New kinetic models with more complete physics have been used to compute the bootstrap current. Predictions of the Sauter model are in general agreement with the newer models for sufficiently collisionless conditions. However, there are often differences for collisional pedestals. An important open issue is that measurements of the edge current density are needed to benchmark predictive models. Searches for the presence of kinetic ballooning modes have been performed in both experiment and simulations. Density fluctuations have been reported in some experiments that have signatures expected of kinetic ballooning modes, including frequency, localization to the 34 pedestal and propagation direction. There have also been observations that the rate of change of the pedestal electron pressure gradient slows or is halted at the time that density fluctuations turn on in the pedestal. These observations are consistent with expectatio ns for KBMs but it has not been shown that they are indeed caused by KBMs. Simulations have been performed for NSTX and DIII - D with electromagnetic gyrokinetic codes to determine if experimental profiles are unstable to KBMs. For calculations with a local model, KBMs have been found to be either sub - dominant to faster growing modes or to lie in a region expected to be second stable to these modes. In a global calculation, the modes were found to be unstable when the experimental reconstructed q - profile was artificially flattened. More experimental and simulation work is needed to clarify whether these modes play a role in the pedestal. A number of models for other physics processes, particularly those relating to the structure of density or temperature prof iles were also tested. The XGC0 code, employing models for kinetic ions and neutral fueling, has been used to examine the combined effect of neoclassical transport and neutral fueling on the density pedestal. The code qualitatively reproduces several featu res of the experiments, including the steep density gradients observed in the H - mode pedestal but typically produces density pedestals that are usually narrower than observed. Some anomalous particle transport is required in addition to neoclassical transp ort to explain the observations. An analytic model for paleoclassical transport has been used to predict features of pedestal electron temperature and density profiles in NSTX and DIII - D. The model has made good predictions of the electron thermal diffusi vity and the shape of the pedestal density profile in NSTX discharges with significant lithium injection. For a range of discharges in DIII - D, the model predicts the minimum observed electron thermal diffusivity. In other cases, additional electron thermal transport must be invoked to explain the results. The model predicts densities that are typically about 2 times larger than observed in DIII - D. Thus, some additional particle transport must be invoked to explain the observations. There are qualitative an d quantitative observations in all machines that have features expected for ETG modes, predicted to limit the pedestal € T e gradient. For instance, the ratio of 35 the electron density scale length to the electron temperature scale length i n the pedestal is ~1 – 3, a magnitude that is expected to destabilize ETG modes. In addition, short wavelength fluctuations, in a range expected for ETG modes, have been observed at the edge of both NSTX and DIII - D. So far, though, there is no clear measurem ent of the amount of transport driven by ETG modes. Thus, they remain as candidates for important pedestal processes. Linear calculations with electromagnetic gyrokinetic codes have been made to identify important fluctuation processes in and near the pede stal. These efforts find evidence of ITG and/or microtearing instabilities on the pedestal top and smaller scale, electron modes in the steep gradient region of the pedestal. However, the results are complex and machine - dependent and it is not yet clear if there is a consistent set of modes present in and on top of the pedestal. This work showed that edge magnetic geometry is important in the physics of these instabilities and must be properly modeled for accurate results. Simulations of EDA discharges in C - Mod with a two - fluid turbulence code predict that unstable modes exist in the pedestal when the resistivity is high. These modes have several characteristics of the quasi - coherent (QC) modes observed in the C - Mod pedestal in these discharges. Experimenta l and modeling evidence suggest that both atomic physics and a pinch play a role in controlling the density pedestal. Some of the strongest evidence in favor of a pinch is interpretive modeling, based on combined constraints of particle and momentum balanc e, which implies that a strong inward force plays a dominant role in molding the density profile. Some of the strongest evidence in favor of fueling was an experiment in NSTX in which the density profile shape was dramatically changed when the deuterium re cycling coefficient was reduced by about an order of magnitude. However, it has so far not been possible to directly measure a pinch in the pedestal in experiments. In combination, these results suggest that both transport (pinch) and fueling effects play a role in the density profile shape and that the importance of these effects may be regime dependent. Overall, these results provide increased confidence that some elements of pedestal structure (P - B stability, bootstrap current and pedestal gradient limit s) are sufficiently well understood to 36 allow for an understanding of limits to the pedestal pressure profile. This understanding can be used to predict the pedestal height in ITER with good confidence. For the ITER baseline scenario, the predicted pedestal temperature is in the range needed to get fusion € Q = 10 , as implied by several transport models [1]. In addition, this understanding provides the important ability to perform pedestal optimization studies in existing and future m achines. An important next step for pedestal modeling is an understanding of the physics of the density and/or temperature profile. A predictive capability for one or both of these profiles will provide a more complete and powerful capability for designing and optimizing the next generation of machines.

评论 (0)