- 标题
- Preface
- 语言
- en
- pages
- vii–x
- 原文
- <!-- page: 7 -->
Preface
Nuclear reactions provide a virtually inexhaustible source of energy, which can be
harnessed in the process of either fusion of light elements (e.g., hydrogen isotopes)
or splitting heavy elements (e.g., uranium, plutonium, thorium, etc.). In both cases,
the total mass of the initial nuclei, Min, is larger than the total mass of the products,
Mpr, of the nuclear reactions. Then, from the famous relation between the energy and
mass, E ¼ Mc2 (where c is the speed of light), and the energy conservation law, the
energy ΔE ¼ (Min Mpr) c2 goes into the kinetic energy of the products of the
nuclear reactions. This is somewhat similar to what happens when we burn fossil
fuels, where, however, we operate with the energy of chemical bonds of fossil fuel.
The fusion process requires the rapprochement of nuclei to a really small distance.
Since the nuclei are positively charged, this is only possible when the initial kinetic
energy (temperature) of the nuclei is large enough to overcome the strong repulsive
electric force. Thus, nuclear fusion is only possible at large temperatures ~108 K
which correspond to ~104 eV, where eV is the energy/temperature unit widely used
in physics. This makes nuclear fusion to be very different from fission, where the
release of nuclear energy occurs in the processes of the interaction of the nucleon
with a neutron (having zero electric charge and, therefore, not subject to the electric
force) and can proceed even at the room temperature. The harnessing of nuclear
energy via the fusion process is a challenging endeavor. First, the fusion fuel must be
heated by an external energy source to a very high temperature to turn the fusion
reactions on. Secondly, the high temperature of the fuel can be maintained by the
release of nuclear energy only when the energy leakage from the fusion fuel is
relatively slow, or, as physicists usually say, energy “confinement” or thermal
insulation of the fusion fuel is good enough. Thus, again, we see that fusion is
similar to the process of burning fossil fuel, which usually occurs at an elevated
temperature maintained by the release of the chemical energy and the proper energy
confinement. Finally, the extremely high temperatures needed for fusion reactions
make it impossible to use any solid material-based furnace for the “confinement” of
the fusion fuel. This is in striking contrast to the “furnace” fired by fission or fossil
vii
<!-- page: 8 -->
viii Preface
fuel, having the “burning temperatures” compatible with many materials (such as
metals or ceramics).
Today, there are two major approaches to confining the fusion fuel at the fusion-
relevant temperatures. The first one is the so-called “inertial confinement,” where the
hot fusion fuel is actually not really confined, but the fuel is burned down so fast that
it has not enough time to cool down. In a sense, this approach is analogous to what
happens during the explosion of an H-bomb, but on a much smaller scale tolerable
for the apparatus designed for the inertial confinement. The second one utilizes the
fundamental feature of the matter at high temperatures, where electrons are stripped
from neutral atoms, which results in the formation of plasma consisting of negatively
charged electrons and positively charged ions.
It should be noted that the plasma we consider in this book has virtually no net
charge since due to the different signs of the charge of electrons and ions, they attract
each other so that the plasma largely moves as a quasi-neutral “fluid” and its inertial
confinement lifetime is determined by the thermal speed of ions which are much
heavier than electrons. At the fusion temperatures ~108 K, the thermal speed of the
ions (nuclei) of hydrogen isotopes is about 106 m/s. Therefore, if one makes no effort
to confine such a quasi-neutral motion of plasma, the latter would be disintegrated
and cooled down within a short time (this is what actually happens in the inertial
confinement devices). The addition of an external magnetic field drastically changes
the plasma dynamics. Indeed, the charged particles, being subject to the Lorentz
force, cannot move freely across the magnetic field. Instead, they undergo gyro-
motion around the magnetic field lines. By applying a strong magnetic field, the
gyro-radii of both electrons and ions can be made much smaller than the size of the
apparatus (e.g., for the fusion-relevant temperatures and the strength of the magnetic
field ~1 T, the gyro-radii of the ions of hydrogen isotopes are ~102 m). In addition,
to prevent the particle leakage along the magnetic field lines, one can utilize a closed
toroidal configuration of the external magnetic field so that the charged particles can
only escape across the magnetic field. This is the second major approach to confining
the hot fusion fuel, which is called “magnetic confinement,” Stellarator and tokamak
are two, the most known and advanced, fusion devices using the magnetic confine-
ment. Stellarator, from “stellar,” suggests the device that produces energy like stars,
for example, the Sun. The “tokamak” is an acronym of Russian words “current,”
“chamber,” and “magnetic coils.”
The magnetic field in the magnetic confinement devices (e.g., tokamaks) does not
solve automatically all issues related to harnessing the fusion energy. The fusion-
grade plasma is very “fragile” and sensitive to the presence of impurities
(non-hydrogenic species) since they open the plasma energy sink by strongly
enhancing the radiation losses and cooling down the plasma very efficiently (e.g.,
the relative concentration of a heavy impurity such as tungsten in a fusion-grade
plasma must be below 104). Therefore, fusion plasma, embedded into a strong
magnetic field, must be insulated from the atmosphere in some vacuum chamber.
The plasma-facing material (PFM) of the vacuum chamber, however, can be eroded
by the impinging ions of even much smaller energy (~few tens of eV) than needed
for fusion. As a result of such erosion, individual atoms, clusters, and even
<!-- page: 9 -->
Preface ix
microscopic dust particles from the PFM can penetrate into the fusion grade plasma
and cool it down, thus killing the fusion reactions. Therefore, the plasma temperature
in the vicinity of the PFM should be below the erosion threshold (preferably ~ 1 eV)
to avoid such catastrophic scenarios. As we see, we are facing a very challenging
issue: to ensure a descent rate of the fusion reactions, the core plasma temperature
must be ~104 eV, whereas the plasma temperature near the plasma-facing compo-
nents (PFCs) situated at the distance ~ 1 m from the core should be in the range of
1 eV.
An additional complication is that the magnetic confinement of plasma is not
perfect. First, there is so-called “classical” transport of the plasma energy and
particles across the magnetic field associated with collisions of the charged particles.
Secondly, there is also the so-called “anomalous” plasma leakage across the mag-
netic field, which is related to the turbulent electromagnetic fields driven by different
plasma instabilities, which often exceeds classical transport by orders of magnitude.
As a result, both the energy and particles (in particular, the products of fusion
reactions, the so-called “ash”—helium for the case of the deuterium-tritium reac-
tions) are transported from the core to the peripheral region. Although this can heat
the plasma near the PFCs above the erosion limit, it allows removing the ash and
prevents the “poisoning” of the magnetic fusion device with the ash. Yet, the energy
transport to the PFCs can be strongly non-uniform and cause a local overheating of
the PFCs beyond the acceptable level. All these issues, associated with the exhaust
of fusion energy and ash, are controlled by plasma transport processes in the
peripheral region of magnetic fusion devices close to the PFCs (which is usually
called the “edge plasma”).
Transport processes in edge plasmas are complex and nonlinear and often result
in the formation of the plasma transport barrier and the transition of the entire
magnetic fusion device to a high-confinement operation regime (the so-called “H-
mode”). Today, it is assumed that all future magnetic fusion reactors (such as ITER
which is under construction in France, and the first electric power generating device
DEMO which is under discussion) will be operating in H-mode. At the same time,
steep variations of the plasma parameters within the transport barrier can trigger
violent plasma instabilities causing rapid expulsion of hot (~ few keV) plasma
towards the PFCs, which for the reactor-relevant parameters can have catastrophic
consequences for the PFM.
Thus, we see that the edge plasma plays a crucial and multifaceted role in
magnetic fusion devices: on the one hand, it sets the plasma confinement which
defines virtually all major parameters of the magnetic fusion reactor (e.g., the size of
the apparatus and the magnetic field strength), whereas on the other hand, it
determines the energy and ash exhaust as well as the plasma interaction with the
PFCs, which, in addition to the potential threat of core plasma contamination by the
eroded material, control the lifetime of the entire device. As a matter of fact, the latter
issues were recognized by such “founding fathers” of magnetic fusion as A. D.
Sakharov and L. Spitzer already at the dawn of the era of magnetic fusion research.
Today, it is widely accepted that without reliable solutions to the outstanding issues
<!-- page: 10 -->
x Preface
of edge plasma physics, no magnetic fusion reactor is possible, and the edge plasma
physics becomes the forefront of magnetic fusion research.
In this book, we present the core of the modern understanding of the most crucial
edge plasma phenomena. Since edge plasma physics is very complex and involves
many different topics ranging from classical and anomalous transport of
multispecies plasma to atomic physics, the energy radiation loss and radiation
transport in opaque media, the plasma material interactions and even the material
physics, we cannot describe here all these topics in detail. In many instances, we will
emphasize the theoretical background of the underlying physics process and illus-
trate our conclusions with the available experimental data while referring to other
books, review papers, and journal publications for the details. At this time, there are
hundreds and thousands of journal publications devoted to different aspects of the
edge plasma physic, so it is impossible to cite all of them. We hope that our
colleagues understand this and will not be too upset if some of their publications
are absent from the reference list.
La Jolla, CA, USA Sergei Krasheninnikov
Saskatoon, SK, Canada Andrei Smolyakov
Moscow, Russia Andrei Kukushkin
- source_type
- 关联原件转录,保留分页及转录字符
评论 (0)